Skip to main content

 

Electronic Theatre Controls Inc

Emphasis Console Default Settings

Console Application Defaults

The following default settings are for reference only. They are not intended as instruction on what the correct settings for your system should be. These settings can be changed from either Emphasis Visualization or Emphasis Console. In Visualization these can be set from the EMPHASIS mode, then Setup. In Console, these can be found in the main Emphasis Console Application box. They are set under their headings in Options. Visualization should the application of choice for setting these parameters.

Emphasis Console Settings-1.png

 

The following are only set from Visualization. These can be found in the Emphasis Mode, then Options, then Application Options. Most settings are the defaults of WYSIWYG, only the one specific to Emphasis are covered here:

Emphasis Console Settings-2.png

 

The following are set from the Emphasis Console Application only. These can be found in the main Emphasis Console Application box. They are set under their headings in Options:

Emphasis Console Settings-3.png

Expression Facepanel Defaults

ETCNet2  
Emphasis RPU System ID A 0
Emphasis RPU System ID B -
IP Address 10.101.45.101
Gateway Address 10.101.45.101
Subnet Mask 255.255.0.0
Display Processor List Disabled
Label Defaults to the type of console it is in
Use Configured IP Parameters Disabled

 

DMX  
Local DMX/EDMX input/output enabled  
DMX Output Port Timing Max
DMX Output Port 1 Start Channel 1
DMX Output Port 1 Channel Count 512
DMX Output Port 2 Start Channel 513
DMX Output Port 2 Channel Count 512
DMX Output Port 3 Start Channel 1025
DMX Output Port 3 Channel Count 512
DMX Output Port 4 Start Channel 1537
DMX Output Port  Channel Count 512
DMX Input Port Start Channel Number 10001
DMX Input Port Channel Count 512
DMX Input Port Disabled
DMX Input Port Priority 10

 

MIDI  
MIDI Input Port EMIDI ID 1
MIDI Output Port EMIDI ID 2

 

SMPTE  
SMPTE Input Port ESMPTE ID 1
SMPTE Inport Port Frames per SEcond 30
SMPTE Start-of-Loop (HH:MM:SS:FF) 0:0:0:0
SMPTE End-of-Loop (HH:MM:SS:FF) 23:59:59:29

 

Remote Macro    
Remote Macros 1-8 Macro ID 1901-1908 System ID 0
Remote Macros 9-16 Macro ID 1909-1916 System ID 0
Remote Macros 17-24 Macro ID 1917-1924 System ID 0
Remote Macros 25-32 Macro ID 1925-1932 System ID 0

 

Lighting Playback Controller  
Lighting playback controller mode Disabled

 

Serial Button Protocol  
Use serial port for button protocol Disabled
Baud Rate 115200

Express Facepanel Defaults

ETCNet2  
Emphasis RPU System 0
IP Address 10.101.45.101
Gateway Address 10.101.45.101
Subnet Mask 255.255.0.0
Display Processor List Enabled
Label Defaults to the type of console it is in
Use Configured IP Parameters Disabled

 

DMX  
Local DMX/EDMX input/output enabled  
DMX Output Port Timing Max
DMX Output Port 1 Start Channel 1
DMX Output Port 1 Channel Count 512
DMX Output Port 2 Start Channel 513
DMX Output Port 2 Channel Count 512

 

MIDI  
MIDI Input Port EMIDI ID 1
MIDI Output Port EMIDI ID 2

 

Remote Macro  
Remote Macro 1 System ID 0
Remote Macro 1 Macro ID 1901
Remote Macro 2 System ID 0
Remote Macro 2 Macro ID 1902
Remote Macro 3 System ID 0
Remote Macro 3 Macro ID 1903
Remote Macro 4 System ID 0
Remote Macro 4 Macro ID 1904
Trigger Out System ID 0
Trigger Out Trigger ID 1

 

Serial Button Protocol  
Use serial port for button protocol Disabled
Baud Rate 115200
  • Was this article helpful?