Sensor+
Looking for the Sensor+ (CEM+) manuals or other documentation? Click here!
Looking for the Sensor+ Installation Rack documentation? Click here!
Looking for the latest version of the User Interface Simulation? Click here!
- Sensor+ Hardware
- Are Sensor ThruPower Modules Compatible with Classic or Sensor+ Racks
- Can a Sensor3 Battery Backup or Ride-thru Option Module be Installed in a Sensor+ Rack
- Can I Upgrade a Sensor+ SineWave Rack to Sensor 3?
- Can I use more than one wire on a load lug in a Sensor+ rack?
- CEM Fan Timeout in Sensor+
- CEM+ LCD Scrambled
- CEM+ Not Powering On
- CEM+ Pulled While System Was Live
- CEM+ Reporting Overtemp Error
- CEM+ screen is flickering, has voltage errors, isn't powering on at all, and/or keeps rebooting
- CEM+ Test Mode Activation
- CEM+ Backplane Comm Error
- CEM+ Locking Up/Freezing
- CEM+ Power Usage
- CEM+ processors that can't be downgraded below v3.1.2
- Cleaning Sensor Dimmer Rack Air Filters and Modules
- Control Module (CEM) Powers on but Not All Dimmers Work in Sensor Rack
- Convert a SR12 from 3 Phase to Single Phase
- Dimmer Order Incorrect After Upgrading Sensor Classic Touring and Delta 1 Racks
- Dimming Modules Function in My Rack, but Other Modules Do Not
- Fan Harness Polarity for Sensor+ to Sensor3 Rack Upgrades
- Flickering in a Sensor Rack
- Harmonic Disturbances Directive EN61000.3.2
- How to Replace a Power Cube in a Sensor Dimming Module
- Is there a RideThru or BatteryPack option available for Sensor+?
- Locating DMX Chips on a CEM+
- Neutral Quad Lugs for Sensor Racks
- Number of Load Grounds Can Land In A SR48
- Passive DMX through a Sensor+ Rack
- Phasing in Sensor Portable Packs and Touring Racks
- Proper Installation of Dimmer Modules in Sensor+ SineWave Racks
- Ribbon Cable Conversion Board Version 2 and Sensor Classic to CEM+ Upgrade Kits
- Running Conduit into the Sides of a Sensor Rack
- Sensor 3 Fuse Tap Kit Cannot Be Used in Racks Which Were Upgraded from +
- Sensor and Unison US 120v Rack Fan Noise Information and Sensor Sound Suppression 'SSSh' Hoods and Skirts 'SSSs' 'SPL' or 'DB'
- Sensor Delta Rack J1 Pinout
- Sensor+ Fan Not Working
- Sensor Module and Rack AIC ratings
- Sensor Rack Phasing
- Sensor Rack to Work in Single Phase?
- Sensor+ Backplane Repairs
- Sensor CEM Test Switch (classic, +, or 3)
- Sensor+ Manuals (CE)
- Sensor+ Reporting Backplane Comm Failure
- Setting DMX Address on the CEM+ (Basic/Portable)
- Should Signal Lights on Modules in Sensor+ Rack Dim with Loads
- Updating CEM+ to CEM3
- What are the Fuse Changes for a Delta CEM?
- What do the LEDs on a CEM+ mean?
- What do the LED indicators on the CEM+ SmartLink Power Board indicate?
- What Is the Correct Fan Orientation in a Sensor + Install Rack?
- Which Phase Powers the Sensor Processor?
- Sensor+ Software
- Can't Open the CEM+ Editor by Double-Clicking on Icon in Net3 Concert Workspace
- Can SmartLink Stations Talk to DMX Addresses Units Other than Sensor Circuits
- Not All Firing Modes Function with ELV10 in a Sensor+ Rack
- CEM+ and Outputting DMX
- CEM+ Config Backed Up When Updating With UpdaterAtor
- CEM+ hardware and software version compatibility
- CEM+ processors that can't be downgraded below v3.1.2
- CEM+ Stops Listening to sACN Data Until Restarted
- CEM+ User Interface Emulation v1.2.0
- CEM+ User Interface Emulation v2.2.0
- CEM+ User Interface Emulation v3.1.3
- CEM+ Will Not Hold a Configuration
- CEM+ Won't Connect to Concert But Will Connect to Updaterator
- Change The Contrast on My CEM+
- Dimmer Curves for Sensor+
- Generate Defaults Sensor CEM+ Full Feature & Basic Portable
- How do I Change Module Type on a CEM+?
- How to change the firing mode of a dimmer on CEM+?
- How to Enable and Access Dimmer Feedback for Sensor+ on Eos Family Console
- How to Get Sensor+ (CEM+) Rack Config from Another Rack in the System
- How to Load a Saved Configuration via the webUI
- How to Set DMX Loss Behavior on CEM+
- How to Set Levels (Turn on Dimmers Locally) in CEM+
- How to update software on a CEM+ module
- LCD Blackout During CEM+ 3.0 Update
- Matching Intensities And Dimmer Curves Between A Sensor Classic CEM, CEM+, And CEM3 Control Processors
- Minimum Levels in CEM+
- Newer CEM+ Will Not Load Configuration from Older or Upgraded Multi-Rack System
- Saving CEM+ Processor Configuration Files to a PC
- SCR Failure All Dimmers or AF Card Error Displays Sensor+
- Sensor CEM+ Menu Structure
- Sensor+ (CEM+) Connect for Microsoft Edge
- Sensor+ (CEM+) Connect WebUI and Internet Explorer
- Sensor+ (CEM+) Connect with Internet Explorer 11
- Sensor+ (CEM+) Connect with Internet Explorer 7
- Sensor+ (CEM+) Connect with Internet Explorer 8
- Sensor+ (CEM+) Connect with Internet Explorer 9 and above
- Setting Up a Loaner CEM+ Processor
- What's the earliest Software Version CEM+ can run and still receive sACN from Paradigm?
- Which CEM+ Versions Can Be Configured with Concert?
- Why can't I add my CEM+ rack in Concert