Sensor Classic
Looking for the Sensor Classic (CEM) manuals or other documentation? Click here!
Looking for the Sensor Classic Installation Rack documentation? Click here!
Looking for the latest version of the User Interface Simulation? Click here!
- Sensor Classic Hardware
- Are Sensor ThruPower Modules Compatible with Sensor Classic Racks
- Can I Put and Sensor Classic CEM into a Rack that had an MPE?
- Can I Unbuss my Sensor Classic Rack?
- Can I use more than one wire on a load lug in a Sensor Classic rack?
- Can you configure an MPE to be Switched/Non-Dim?
- CEM Classic Power Usage
- CEM Classic says Airflow Problems or No Airflow
- CEM CPU PCB Functional Diagram
- CEM Fan Timeout in Sensor Classic
- CEM UPSAC J6 Connector Pinout
- Cleaning Sensor Dimmer Rack Air Filters and Modules
- Control Module (CEM) Powers on but Not All Dimmers Work in Sensor Rack
- Convert a SR12 From 3 Phase to Single Phase
- D20F Module Q141 and Q142 Power Cube Changes
- Dimmer Doubling (Multiplexing) On The Sensor MPE
- Dimmer Order Incorrect After Upgrading Sensor Classic Touring and Delta 1 Racks
- Dimmer Overtemp Errors on Sensor CEM classic
- Dimming Modules Function in My Rack, but Other Modules Do Not
- End-Of-Line DMX512 and ETCLink Termination on Sensor CEM
- ETCLink Termination and Ice Cube
- Fan Harness Polarity for Sensor Classic to Sensor3 Rack Upgrades
- Flickering in a Sensor Rack
- Harmonic Disturbances Directive EN61000.3.2
- How to Replace a Power Cube in a Sensor Dimming Module
- How To Use Panic On A CEM Backplane
- Jumper Settings For Sensor Backup Station PCBs
- LED 1 Blinking on Sensor Backup Station
- LED 1 Glows at Low Level on Sensor Backup Station
- Neutral Quad Lugs for Sensor Racks
- Number of Load Grounds Can Land In A SR48
- Passive DMX Wiring Through Sensor Rack
- Phasing in Sensor Portable Packs and Touring Racks
- Replacing an airflow sensor (TS107) on a Sensor Classic CEM
- Ribbon Cable Conversion Board Version 2 and Sensor Classic to +/3 Upgrade Kits
- Running Conduit into the Sides of a Sensor Rack
- Sensor 3 Fuse Tap Kit Cannot Be Used in Racks Which Were Upgraded from Classic or +
- Sensor and Unison US 120v Rack Fan Noise Information and Sensor Sound Suppression 'SSSh' Hoods and Skirts 'SSSs' 'SPL' or 'DB'
- Sensor Backup Station: All LEDs Blink When a Button is Pressed
- Sensor Backup Station Pinout
- Sensor CEM Displays Airflow Errors and May Flash Loads
- Sensor CEM Software Revisions
- Sensor CEM Test Switch
- Sensor CE (European) Installation (ESR) Rack Fan Noise Information and Sensor Sound Suppression 'SSSh' Hoods & Skirts 'SSSs' 'SPL' or 'DB'
- Sensor Classic Compatibility with new R20AF modules
- Sensor Classic Low Voltage Pinout (J2)
- Sensor Classic Ribbon Cable Specifications
- Sensor Control Electronics Module (CEM) Fuses
- Sensor Module and Rack AIC ratings
- Sensor MPE DIP Switches
- Sensor MPE DMX - LED Solid or Blinking
- Sensor MPE Fuses
- Sensor MPE in SR6 Rack - Goes into Alarm and Dimmer Output Turns Off Shortly After Being Commanded On
- Sensor MPE Self-Tests
- Sensor Overtemp Operation
- Sensor Rack Phasing
- Sensor Rack to Work in Single Phase?
- Sensor Signal Distribution (Distro) Cards
- Sensor Single Phase Rack Phase Balancing
- Sensor Touring Rack CEM Classic Data Backplane Pinout
- Should Signal Lights on Modules in Sensor Classic Rack Dim with Loads
- Terminate ETCLink On A Sensor Backup Station
- Updating CEM Classic to CEM3
- What are the Fuse Changes for a Delta CEM?
- What fan is used in the SR6?
- What Is the Correct Fan Orientation in a Sensor Classic Install Rack?
- Which Phase Powers the Sensor Processor?
- Why Don't ThruPower Modules Fit Into My Old Sensor Portable Rack?
- Sensor Classic Software
- AF Sensor Rack Dimmer Module Changes (AFM)
- CEM "Backup Mismatch" Error
- CEM Classic Power Usage
- CEM Classic User Interface Emulation v2.14
- CEM Classic User Interface Emulation v3.21
- CEM "Config Mismatch" Error
- Clear Overtemp, Airflow, and other Sticky Errors On The Sensor CEM
- Computer Requirements for SLTA
- Dimmer Curves for Sensor Classic
- Dimmer Doubling DD (Multiplexing) sets Threshold to 50%
- Display on CEM Says System Error
- ETCLink Support Limitations
- Finding the Software Version of a Sensor Classic CEM
- Generate Defaults Sensor CEM Classic-All Versions
- How to Change Firing Mode of a Dimmer to Switched on Sensor (CEM) Classic
- How to Set Up Dimmer Doubling Multiplexing In Sensor Classic Rack
- How to turn a DMX port on and off on CEM Classic
- Matching Intensities And Dimmer Curves Between A Sensor Classic CEM, CEM+, And CEM3 Control Processors
- Running Sensor On-Line on Newer Computers
- SCR Failure All Dimmers or AF Card Error Displays Sensor Classic
- Sensor 2.04 ABOUT and SETUP not Responding to Button Hits
- Sensor 3.x Mixing Versions of Software
- Sensor Backup Looks Not Playing Correctly In All Racks In A Multi Rack System
- Sensor CEM Classic Menu Structure
- Sensor CEM Displays "Airflow Errors" and May Flash Loads
- Sensor CEM Test Switch
- Sensor Classic Software
- Sensor Touring Rack CEM Classic Data Backplane Pinout-Public
- Sensor Unique Dimmer Numbers in Sensor Classic
- Setting Up a Loaner CEM Classic Processor
- Setup A Dimmer To Be Always On In Sensor Classic 2.14 Software
- Set Levels Locally at Sensor CEM Classic