Sensor3
Looking for the Sensor3 (CEM3) manuals or other documentation? Click here!
Looking for the latest version of the User Interface Simulation? Click here!
- Sensor3 Hardware
- Are AF Cards Replaced In a CEM to CEM3 Upgrade?
- Can a Sensor3 Battery Backup or Ride-thru Option Module be Installed in a Sensor+ Rack
- Can I use more than one wire on a load lug in a Sensor3 rack?
- Can Sensor3 (CEM3) Output DMX?
- Can wiring from a Sensor3 Battery Backup and a network cable be run in the same conduit?
- CEM3 Fan Fail Error
- CEM3 Front Ethernet Port Problems
- CEM3 LCD Backlight Dimming Up and Down
- CEM3 Network Port POE
- CEM3 Not Powering Up
- CEM Fan Timeout in Sensor Racks
- Cleaning Sensor Dimmer Rack Air Filters and Modules
- Control Module (CEM) Powers on but Not All Dimmers Work in Sensor Rack
- Dimmers in Wrong Order after Upgrading Sensor Classic Touring and Delta 1 Racks
- Dimming Modules Function in My Rack, but Other Modules Do Not
- Fan Harness Polarity for Sensor3 Rack Upgrades
- First Time Setup Backplane Dipswitches
- Harmonic Disturbances Directive EN61000.3.2
- How to Deep Clear a CEM3 Processor
- How to Replace a Power Cube in a Sensor Dimming Module
- Module Coverage in Power Package Warranty
- My Ride Thru Option Card is Not Lasting 10 Seconds
- Neutral Quad Lugs for Sensor Racks
- Number of Load Grounds Can Land In A SR48
- Part Number for Sensor Door gasket
- Passive DMX Wiring Through Sensor Racks
- Phasing in Sensor Portable Packs and Touring Racks
- Purpose of Panic Input on Sensor3 Panic Supply
- Replaced CEM3 Backplane and now Echo Stations Do Not Function
- Ribbon Cable Conversion Board Version 2 and Sensor Classic to CEM3 Upgrade Kits
- Running Conduit into the Sides of a Sensor Rack
- Sensor3 AF Cards
- Sensor3 BatteryPack Option
- Sensor3 CEM Test Switch
- Sensor3 Has Blank Screen and Red Panic Light
- Sensor3 LEDs flickering rapidly. Power appears to be flickering
- Sensor3 No output on one or more dimmers/lugs
- Sensor3 Panic Supply switches to Panic Mode, but Keeps Normal Light Illuminated.
- Sensor3 Power Control System
- Sensor3 Processor Stuck on "ETC CEM3" screen
- Sensor 3 (CEM3) 230V Variable Speed Fan Beacon LED states
- Sensor 3 Fuse Tap Kit Cannot Be Used in Racks Which Were Upgraded from Classic or +
- Sensor 3 Overtemp Operation
- Sensor and Unison US 120v Rack Fan Noise Information and Sensor Sound Suppression 'SSSh' Hoods and Skirts 'SSSs' 'SPL' or 'DB'
- Sensor Module and Rack AIC ratings
- Sensor Rack Phasing
- Sensor Rack to Work in Single Phase?
- Setting Up a Loaner CEM3 Processor
- Should Signal Lights on Modules in Sensor3 Rack Dim with Loads
- Updating to a CEM3 Rack
- What are the Fuse Changes for a Delta CEM?
- What Is the Correct Fan Orientation in a Sensor 3 Install Rack?
- Where are the DMX chips on the CEM3?
- Which Phase Powers the Sensor Processor?
- Sensor3 Software
- "Looking for Circuit" Error in Set Circuits on CEM3
- CEM3 Airflow Error
- CEM3 Bootlooping or Resetting
- CEM3 Can Enable or Disable Echo Remote Record
- CEM3 Error States
- CEM3 Not Booting and Appears Stuck in Emergency
- CEM3 Overvoltage Error
- CEM3 Power Control
- CEM3 Reporting Over-voltage, Under-voltage, and Frequency Errors
- CEM3 Stuck on ETC CEM3 Screen
- CEM3 Tips And Tricks
- CEM3 User Interface Emulation v1.6.1
- CEM3 User Interface Emulation v1.7.1
- Change Rack Number
- Changing Fan Timeout on CEM3 Processors
- Changing Rack Number on CEM3
- Changing Sensor Thru-Power Circuit Mode from Eos
- Configuration Behavior When Moving a CEM3 Between Racks
- Dimmer Curves for Sensor3
- Dimmer Property Definitions
- Dimmer Setup
- Enabling 16-bit Fade Control on CEM 3
- Enabling Or Disabling Data Ports
- Enabling Quick Setup Button on CEM3
- FTP Server Setup for CEM3 (with Net3 Conductor)
- Generating QR Codes for Sensor TPSR
- GrandMA Control is Slow or Does not Work with Sensor3
- How Do I Edit Custom Dimmer Curves For My CEM3?
- How to Change the Start Address on Sensor3 (CEM3)
- How to Enable and Access Dimmer Feedback for Sensor+ and Sensor3 on Eos Family Console
- How to Save and Load a Configuration to a CEM3 Processor
- How to Set Local Levels on a Sensor CEM3
- How To View CEM3 Errors on an Eos Console
- Matching Intensities And Dimmer Curves Between A Sensor Classic CEM, CEM+, And CEM3 Control Processors
- Minimum Levels in CEM3
- No Control of Sensor3 via Console and Screen Says "Preset Active"
- Presets in Sensor 3
- Sensor3 (CEM3) Quick Setup (Typically Used in Touring and Portables)
- Setting Data Loss Behavior On The CEM3
- Setting Levels on a CEM3 Changes Levels in Multiple Racks
- Swapping out a CEM3 Processor
- TPSR app does not work over a routed network
- Voltage Range Warning Adjustment
- What is the maximum number of sACN universes that a CEM3 supports?